This "to scale" dollhouse outlet is, to our knowledge, the smallest working outlet ever made, measuring a mere .414" high by .3" wide by .13" thick. And installation couldn't be easier. Simply place over the tape run at the desired location and pound in.

The CK1003 outlet nails are imbedded diagonally, allowing the outlet to be mounted vertically regardless of whether the tape run is vertical or horizontal. By using the CK204 Test Probe to locate the tape run, the outlet can be installed even
after wallpapering.

Each outlet is constructed of tough, white plastic with tapered edges to achieve an authentic outlet look. The double set of holes will accommodate two CK1004 or CK1004-2 plugs and provides a convenient means of electrifying any miniature floor or table lamp. Each package also contains 1/4" brass brads for use as marker pins when wallpapering. 600 ma current rating.

For those not wishing to discard the CK1004-3 plug, our CK1023-2 eyelets provide a simple alternative. First, using the plug attached to the lamp as a guide, mark two holes on the tape run. Then, using either the CK1044 Awl or a No. 52 drill bit, make two starter holes and insert eyelets. The lamp plug may now be directly inserted, making for an attractively flush and easy to install outlet.

Eyelets are brass and measure approximately 3/16" long with an inside diameter of .054" and outside diameter of .071". Packaged in quantities of 100. Illustrated instructions in package.

These high quality bulbs are excellent for illuminating any part of a dollhouse or miniature room.  Bulb wires may be attached to our miniature plugs or directly bradded into tape runs with 1/8" brass brads.

The 12-volt bulbs should be used in locations where bright illumination is necessary and the 16-volt bulbs in areas where a soft, non-glaring light is preferred.

The grain-of-wheat (GOW) bulbs measure approximately 1/8" in diameter and draw between 40-60 ma.

In addition to the above the grain-of-rice (GOR) bulbs are ideal for those applications where minimum bulb size is desirable.

These bulbs are made with some of the smallest insulated wires available.  Great attention has also been given to making the wire connections at the base of the bulb as unnoticeable as possible.

The GOR bulbs measure approximately 3/32" in diameter and draw between 40-60 ma.

The CK1010-5 bulb is designed for special applications where regular GOW and GOR type bulbs may not be suitable. This bulb allows a practical and most cost effective means of providing light in a multitude of different applications. It may be used alone as a light source or covered with any number of shades for a made-to-order ceiling fixture. This bulb is also a replacement for those included in the CK500 series of ceiling light kits.

The bulb measures approximately 3/32" in diameter by 1/4" in length with 1" wire terminals. Current draw is between 40-50 ma when connected across a 12-volt power source. May also be used with the CK1010-16 and -17 series of candle bodies as a direct plug-in type bulb. 5,000 hour bulb life.

These are the smallest flame-tip bulbs to be found anywhere, measuring a mere .079" (2.0 mm) in diameter. Use wherever a "to scale" flame look is desired. Excellent for chandeliers, sconces, and coach lamps requiring extremely small bulbs. Comes with solid 1" wire terminals.
Current drain: 40 ma.

The CK1010-12 bulbs should be used in conjunction with the CK1010-16 and -17 candle bodies to create fixtures with easily replaceable bulbs. 2,500 hour bulb life.

Ideal for back lighting or illuminating miniatures, these fluorescent shaped bulbs provide a unique and effective indirect lighting source. Available in either frosted or clear tubular glass. The frosted bulb gives a uniform and diffused light over a large area whereas the clear bulbs display a brighter and more localized illumination. Fuse-type snap-in/snap-out construction allows easy bulb installation and replacement.

Each bulb measures approximately 1/4" in diameter by 1-1/2" in length. Power consumption for the CK1018-1 and -2 bulbs is 70 to 80 ma when connected across a 12-volt source. The extra-bright Showcase Bulb draws approximately 220 ma of current. All fluorettes are warranted for 3,000 hours when used with a Cir-Kit Concepts' 12-volt transformer. Mate with CK1019 and CK1019-1 sockets. 2,500 hour bulb life.

These 1.5 volt axial bulbs are a fraction the size of our popular micro bulbs and meet the challenge of even the smallest lighting projects. Ideal as light sources for both 1/4" and 1/2" scale miniatures.

Both size axial bulbs may be operated in parallel either from a 1.5 volt battery pack or from our CK1009G 1.5 volt transformer. The larger diameter CK1010-19 bulbs are electrically balanced and may be operated 12 in series across a 12-volt transformer.

The bulbs may also be used in model railroading for locomotive number boards or classification lights as well as interior lighting for smaller scale cars. 1,000 hour bulb life.

The CK1004-2 is an adaptation of our regular CK1004 Plug. The wires are fed into hollow tubes imbedded in the plug and fastened using a fast drying gel type glue. This is probably the easiest technique yet for connecting lamp wires to a plug. Using the glue gel method results in an extremely aesthetic and long-lasting electrical connection. Mates with CK1003 Outlet. Assembly instructions included. 600 ma rating.

Most Cir-Kit table/floor lamps and outside yard lights are now packaged with a Cir-Kit CK1004-2 plug and attachment instructions included at no extra cost. The use of this plug will add a true dimension of scale to any project.