Outlet, Plug, and Switch Products

CK1003 Wall Outlet

This "to scale" dollhouse outlet is, to our knowledge, the smallest working outlet ever made, measuring a mere .414" high by .3" wide by .13" thick. And installation couldn't be easier. Simply place over the tape run at the desired location and pound in.

The CK1003 outlet nails are imbedded diagonally, allowing the outlet to be mounted vertically regardless of whether the tape run is vertical or horizontal. By using the CK204 Test Probe to locate the tape run, the outlet can be installed even
after wallpapering.

Each outlet is constructed of tough, white plastic with tapered edges to achieve an authentic outlet look. The double set of holes will accommodate two CK1004 or CK1004-2 plugs and provides a convenient means of electrifying any miniature floor or table lamp. Each package also contains 1/4" brass brads for use as marker pins when wallpapering. 600 ma current rating.

CK1003

CK1003A Wall Outlet Cover

Give a polished brass look to all your outlets. These bright and heavily engraved covers will provide a rich and finished appearance wherever they are used. The double holes allow ample space for inserting and removing either type of CK1004 plug. Simply place over outlet and press in place.

CK1003A

CK1004 Cir-Kit Plug

The "to scale" CK1004 Plug is made to work with the CK1003 Outlet and may be attached to the bulb wires from any lighting fixture. To make an electrical connection, stripped lamp wires are simply inserted into small holes in the side of the plug and the supplied pins pushed in from the front. Since the plug is not permanently attached to the wires it may be reused time and time again, a real plus! The plug is made of hard, white plastic and extends less than 1/4" when plugged in. Assembly instructions included. 600 ma current rating.

CK1004

CK1004-2 Hollow Tube Plug

The CK1004-2 is an adaptation of our regular CK1004 Plug. The wires are fed into hollow tubes imbedded in the plug and fastened using a fast drying gel type glue. This is probably the easiest technique yet for connecting lamp wires to a plug. Using the glue gel method results in an extremely aesthetic and long-lasting electrical connection. Mates with CK1003 Outlet. Assembly instructions included. 600 ma rating.

Most Cir-Kit table/floor lamps and outside yard lights are now packaged with a Cir-Kit CK1004-2 plug and attachment instructions included at no extra cost. The use of this plug will add a true dimension of scale to any project.

CK1004-2

CK1005 Plug Pins (4 pak)

Extra pin plugs are available in CK1005 4 pak packages.

CK1005

CK1011 Miniature Slide Switch

The "to scale" CK1011 miniature slide switch is the first of its kind ever made in the electronics industry. Most standard models are equipped with a protruding toggle to allow electrical operation. A close look will reveal that the CK1011 has no such toggle-like feature. Instead, it is designed with a smooth sliding outer body to achieve the "on/off" operation. Why this departure from conventional logic? Ease of installation. The switch now comes with separate spring-loaded eyelets. These eyelets, when installed in a tape run, allow the switch to be installed by simply pushing it into the eyelets. No hammering required. No more loose nails, broken toggles, or "on" position pre-setting. Only a straightforward and uncomplicated mounting procedure. Its rugged construction makes it ideal for use in even the hardest of woods. Placement has now become as simple as installing our famous CK1003 "pound-in" outlet. The complete and fully illustrated instructions included with each switch ensures a successful installation every time. Each package also contains 1/4" brass brads for use as marker pins when wallpapering. 600 ma current rating.

CK1023-6 Spring-Loaded Eyelets (2 pak) packages - $1.98

CK1011

CK1011A Brass Switch Plate Cover

Add a finishing touch to all your CK1011 switches. This distinctive brass plate simply snap fits over the switch to give it a rich and decorative appearance. The protruding toggle enhances the "on/off" operation and provides an added look of realism.

CK1011A

CK1048 In-line Switch

Use this switch wherever on/off power control is desired. It may be used on either 12 or 115 volt lines with zip type cords between 16 and 20 gauge. No soldering, only a screwdriver and wire cutter are required for assembly. To connect, disassemble the switch, cut a segment from one conductor, install wires in the switch, and reassemble. Sharp teeth inside the switch make the necessary electrical contacts. This is the same switch as used on the CK1008 series of lead-in wires. Measures 1-1/4" by
5/8".

CK1048

CK1048-1 Small Slide Switch

Our small SPDT slide switch is well suited for round wire systems involving soldered connections in imbedded locations. It may be located in a wall cutout for either room or complete dollhouse power control. Measures 5/8" long by 3/16" wide by 3/8" deep.

CK1048-1